Blue from remote is capped off. White from ceiling to white on remote and white from fan all together.

Add Your Answer

Copper from ceiling to all greens and yellow out of remote. Black 2 from ceiling to black into remote. Works like a charm. A check of the 3 pole next to the single pole under a double switchplate revealed black as the traveler connected to two screws on the 3 pole. Thank you for your interest in this question. Because it has attracted low-quality or spam answers that had to be removed, posting an answer now requires 10 reputation on this site the association bonus does not count. Would you like to answer one of these unanswered questions instead?

wiring - How do I install a ceiling fan remote? - Home Improvement Stack Exchange

Home Questions Tags Users Unanswered. How should I wire a ceiling fan remote where two switches are used to control the fixture? Tester k 54 Mark Mark 11 1 1 2. Are the switches in the same or different locations? Just a word of caution that if your fan speed and light dimmer are only controlled by remote, no pull strings , then bypassing the receiver will not permit you to control your settings. I'm looking at you "Turn of the Century" fans.

Your Answer

Start by turning off the power at the breaker, and verifying it's off with a non-contact voltage tester. Connect all the bare or green grounding conductors together. Connect the white wire from the ceiling to the white wire on the input side of the remote receiver module and the white wire in the fan. Connect the black wire from the ceiling to the black wire on the input side of the remote receiver module.

Connect the blue wire from the output side of the remote receiver module to the blue wire in the fan. Connect the red wire from the ceiling to the black wire in the fan. Cap off the black and white wire from the output side of the remote receiver module. Alternatively, you could wire it like this.

Tester Tester k 54 So the white wire on the receiver is capped? And the blue wire coming out of receiver is capped? You could use the white neutral coming out of the receiver, or the one coming out if the ceiling. It's up to you. More Print this page Share this page.

You can't post conmments that contain an email address. Instant Repair Help over the Phone 6ya. Helpful 0 Not Helpful Flag. Add Your Answer Tips for a great answer: Tell us some more! Your answer needs to include more details to help people. You can't post answers that contain an email address. Please enter a valid email address. The email address entered is already associated to an account. Login to post Please use English characters only.

The max point reward for answering a question is It's worth a thousand words. Probably need to reset the remote.

Hampton Bay Remote Control Installation issue

I hope you kept the instructions. Also, you might need a new receiver. Minka aire - Any tips as of why? The Mitsu remotes use a smart code function- they send all of the data temp, mode,fan speed,etc. Uni remotes are not built for this in my experience.

You may be able to teach it to so with default functions built in, but I've not yet heard of a good solution for this issue. It's been awhile so you've probably quit by now, but if yo haven't , try this: Get up into the light bowl area nad look for the pull chain on the side of the housing. Pull it 2 times and it should put the motor into high speed. Click the 3 on the remote and see if it goes to high speed. If not, pull the chain and try again. Keep doing this until the motor gets into high speed. It should only take a few times at most. Unit 1 Lowest speed doesn't work at all, middle speed and high speed still working.

How to Wire a Ceiling Fan With a Remote to a Wall Switch : Ceiling Fans & Light Fixtures

Light control work fine. Unit 2 Great difficulty in turning on or You need to completely disassemble the hand held remote unit, remove the rubber push buttons and clean the contacts. Mine do this frequently. The contacts are black and will be slimey. I just use soapy water and a soft cloth to gently clean them. Be sure to dry them completely before reassembling. Also be sure you dont get any of the electronics wet. Some are even recessed in a hole, but if that is the case it should be marked right by the hole.


  • free dating site that works.
  • reality dating shows summer 2020.
  • 6 Suggested Answers.
  • dating website for over 50s.
  • town and country dating nz.

Do you have an instruction sheet for the remote? With Model and Make oftten instructions can be looked up on the internet. Usually at the factory site. Possible the problem is the programing on the remote accidentally was changed. In my case it could have been the button pushing grandson.

Need remote hookup instructions. fan speed is

Remove the battiers in your remote and short out the battery contact terminals. Still no speed change contact the Mgfr. I want a spare so I found this web page page down http: Not finding what you are looking for? Related Question I had a short power surge, and my ceiling fan doesn't work properly. The fan is in a row story family roo and at 70 yrs old I can't get to the fan.